Sraith Seac Ardaithe & Tacaíochta Caibinéid 2-in-1 Fivalo™ (Pacáiste 2)
Two working ratings: up to 360 lb per pair in lift mode; up to 180 lb per pair in extended support mode.
Secure checkout · Product support from Fivalo
Coinnigh an caibinéad san áit cheart—ansin bain úsáid as an dá lámh chun é a leibhéalú, a shimniú agus a cheangal. Athraíonn an córas dhá sheaca seo ó sheacaí ardaithe le raicín go tacaí sínte tríú láimhe agus teanntáin adhmadóireachta, rud a thugann socrú níos rialaithe d’oibrithe aonair óna gcéad choigeartú go dtí an scriú deireanach.
- Tacaíonn dhá sheac chomhoiriúnacha le dhá cheann na hoibre
- Socruithe ardaithe, tacaíochta sínte agus teannta
- Síneadh uasta sonraithe: 23.4 orlach
- Rátáil na beirte: suas le 360 lb sa mhód ardaithe
- Rátáil na beirte: suas le 180 lb sa mhód tacaíochta sínte
- Iarnróid le marcanna scála agus dromchlaí leathana cosanta teagmhála
Stop ag cothromú. Tosaigh ag ailíniú.
Féadfaidh bloic dramhábhair agus tacaí seiftithe bogadh díreach nuair a bhíonn an dá lámh uait. Cuir an bheirt ar dhromchlaí cothroma, cobhsaí, ardaigh gach taobh i gcéimeanna rialaithe, seiceáil an leibhéal agus an t-ailíniú, ansin daingnigh an caibinéad leis na ceanglóirí agus an struchtúr balla atá riachtanach de réir threoracha mhonaróir an chaibinéid.
Trí bhealach oibre
Tacaigh le caibinéid uachtaracha
Ceangail na frámaí leathana tacaíochta agus bain úsáid as an mbeirt faoin gcaibinéad tar éis é a chur go sábháilte ag airde oibre. Coigeartaigh gach taobh agus tú á leibhéalú, á shimniú agus á cheangal.
Ardaigh agus leibhéalaigh
Bain úsáid as na plátaí leathana teagmhála chun caibinéid bhunúsacha, troscán nó píosaí oibre tacaithe a shuíomh thar achar gairid. Coinnigh an t-ualach lárnaithe agus bain úsáid as an dá sheac le chéile.
Teann imill na bpainéal
Cuir na ceangaltáin teannta fhíoraithe isteach chun imill phainéal chomhoiriúnacha a choinneáil agus tú ag seiceáil ailíniú comhréidh. Is le haghaidh coinneáil shealadach oibre atá an mód teannta, ní ionadach é do theanntáin shonracha tionscadail nuair a bhíonn fórsa nó sroicheadh níos mó de dhíth.
Sonraí fíoraithe an táirge
- Leagan: 2 chomhthionól seaca caibinéid
- Síneadh uasta sonraithe: 23.4 orlach
- Bonn thart: 3.7 × 4.1 orlach
- Airde choirp thart: 16 orlach
- Rátáil an mhóid ardaithe: suas le 360 lb in aghaidh na beirte
- Rátáil an mhóid tacaíochta sínte: suas le 180 lb in aghaidh na beirte
Cad atá san áireamh
- 2 × chomhthionól seaca caibinéid
- 4 × cheangaltán gearrthóg/tacaíochta sa dá stíl a thaispeántar
- 6 × chlúdach cosanta
- 1 × lámhleabhar treoracha
Bain úsáid shábháilte as
Soláthraíonn an uirlis seo suíomh agus tacaíocht shealadach; ní prop struchtúrach ná trealamh sábháilteachta lastuas í. Iniúch gach cuid roimh úsáid, oibrigh ar dhromchlaí cothroma cobhsaí, lárnaigh an t-ualach, bain úsáid as an mbeirt le chéile, agus ná sáraigh riamh an rátáil don mhód roghnaithe. Daingnigh an caibinéad le struchtúr balla oiriúnach sula scaoiltear an t-ualach ó na seacaí. Coinnigh do lámha glan ó phointí brúite agus brúigh an scaoileadh de réir a chéile ach amháin tar éis don ualach a bheith tacaithe go neamhspleách.
Sraith Seac Ardaithe & Tacaíochta Caibinéid 2-in-1 Fivalo™ (Pacáiste 2)
Lift, support, and align from a stable paired setup instead of rebuilding a stack of scraps every time the cabinet moves.
Two jacks. Three jobs. Both hands back on the install.
Stop balancing. Start aligning.
Scrap blocks can shift just when you need both hands. Place one jack near each end, raise in controlled steps, then level, shim, and fasten with the cabinet held at the working position.
One matched pair. Three ways to work.
Choose the configuration for the job, then stay inside the rating for that mode.
1. Support upper cabinets
Fit the wide support frames and use the pair beneath a cabinet after it has been safely placed at working height.
2. Lift and level
Use the broad contact plates for short-range positioning under base cabinets, furniture, and supported workpieces.
3. Clamp panel edges
Fit the clamp attachments for temporary workholding while you check flush alignment on compatible panel edges.
Control you can see before the first screw
The mechanism, scales, and contact surfaces are built around controlled positioning—not guesswork.
Scale-marked adjustment
Visible markings make paired height checks easier while you bring each side into position.
Broad contact surfaces
Wide ribbed support plates and rectangular slotted bases spread contact across the working surface.
Ratings matched to the mode
Up to 360 lb per pair for direct lifting; up to 180 lb per pair for extended cabinet support.
From first lift to final fastener
1. Place the pair
Work on flat, stable surfaces with one jack near each end and the load centered on the contact pads.
2. Raise in steps
Alternate between sides and watch the scale marks so the cabinet stays controlled as it reaches position.
3. Align and fasten
Check level and plumb, add required shims, then fasten to suitable wall structure using the cabinet maker’s instructions.
4. Unload, then release
Confirm the cabinet is independently secured, keep hands clear, and press each release gradually before removing the jacks.
Check alignment before the tools come out
The paired setup gives you time to verify level, reveal, and fastener placement while the cabinet stays supported. Once it is secured to the required wall structure, unload each jack and remove it from the work area.
Product details
Verified specifications
Set: 2 cabinet jack assemblies
Listed maximum extension: 23.4 in
Approximate base: 3.7 × 4.1 in
Approximate body height: 16 in
Scale-marked adjustment rails
Mode-specific ratings
Direct lift mode: up to 360 lb per pair.
Extended cabinet-support mode: up to 180 lb per pair.
Use the pair together, keep the load centered, and never exceed the rating for the selected configuration.
What’s included
2 × Cabinet jack assemblies
4 × Clip/support attachments in the two styles shown
6 × Protective covers
1 × Instruction manual
Safe use
Temporary positioning/support only; not structural shoring or overhead safety equipment. Inspect before use, work on flat stable surfaces, secure the cabinet independently before unloading, keep hands clear of pinch points, and press the release gradually.
Frequently asked questions
Can these jacks support an upper cabinet during installation?
Yes. The extended support frames are designed to hold a cabinet after it has been safely placed at working height. Use one jack near each end on a stable surface, then fasten the cabinet to suitable wall structure before unloading the jacks.
How high do they extend?
The manufacturer lists a maximum extension of 23.4 in. Measure from your stable working surface to the cabinet underside and allow for the contact pads before ordering.
What are the load ratings?
The pair is listed for up to 360 lb in direct lift mode and up to 180 lb in extended cabinet-support mode. Do not apply the higher lift rating to the extended support configuration.
Can one person install a cabinet with them?
The jacks can reduce the need to hold and balance the cabinet while aligning and fastening, but they do not replace safe lifting, suitable wall fasteners, or a second person when the cabinet or site conditions require one.
How do I lower the load?
First secure or independently support the load. Keep hands clear of pinch points and press the release gradually. No fine-descent claim is made, so maintain control and never release a loaded jack abruptly.
What comes in the set?
Two cabinet jack assemblies, four clip/support attachments in the two styles shown, six protective covers, and one instruction manual.
A matched two-jack system for installers who want fewer makeshift props and more control at the cabinet.