Fivalo™ 2-i-1 løfte- og støttebukkesæt til skabe (2-pak)
Two working ratings: up to 360 lb per pair in lift mode; up to 180 lb per pair in extended support mode.
Secure checkout · Product support from Fivalo
Hold skabet på plads, hvor det skal være – brug derefter begge hænder til at nivellere, kilesikre og fastgøre det. Dette system med to donkrafte kan omdannes fra donkrafte med palmekanisme til forlængede trediehåndsstøtter og træbearbejdningsklemmer, så gør-det-selv-montører får en mere kontrolleret opsætning fra den første justering til den sidste skrue.
- To ens donkrafte understøtter begge ender af emnet
- Konfigurationer til løft, forlænget understøtning og fastspænding
- Angivet maksimal forlængelse: 23,4 tommer
- Bæreevne for parret: op til 360 lb i løftetilstand
- Bæreevne for parret: op til 180 lb i tilstand med forlænget understøtning
- Skinner med målestreger og brede, beskyttende kontaktflader
Hold op med at balancere. Begynd at justere.
Træklodser og improviserede understøtninger kan flytte sig, netop når du har brug for begge hænder. Placér parret på plane, stabile overflader, hæv hver side i kontrollerede trin, kontrollér niveau og justering, og fastgør derefter skabet med de fastgørelsesmidler og til den vægkonstruktion, som skabsproducenten kræver.
Tre måder at arbejde på
Understøt overskabe
Fastgør de brede støttebeslag, og brug parret under skabet, når det er placeret sikkert i arbejdshøjde. Justér hver side, mens du nivellerer, kiler op og fastgør.
Løft og nivellér
Brug de brede kontaktplader til kortvarig positionering under underskabe, møbler eller understøttede emner. Hold belastningen centreret, og brug begge donkrafte sammen.
Fastspænd pladekanter
Montér de verificerede klemmebeslag for at holde kompatible pladekanter, mens du kontrollerer, at de flugter. Klemmetilstanden er beregnet til midlertidig fastholdelse og erstatter ikke projektspecifikke klemmer, når der kræves større kraft eller rækkevidde.
Verificerede produktoplysninger
- Sæt: 2 skabsdonkrafte
- Angivet maksimal forlængelse: 23,4 tommer
- Omtrentlig fod: 3,7 × 4,1 tommer
- Omtrentlig kropshøjde: 16 tommer
- Bæreevne i løftetilstand: op til 360 lb pr. par
- Bæreevne i tilstand med forlænget understøtning: op til 180 lb pr. par
Dette medfølger
- 2 × skabsdonkrafte
- 4 × clips-/støttebeslag i de to viste typer
- 6 × beskyttelseshætter
- 1 × brugsanvisning
Brug den sikkert
Dette værktøj er beregnet til midlertidig positionering og understøtning; det er ikke en konstruktionsunderstøtning eller sikkerhedsudstyr til arbejde over hovedet. Kontrollér alle dele før brug, arbejd på plane, stabile overflader, centrér belastningen, brug parret sammen, og overskrid aldrig den angivne bæreevne for den valgte tilstand. Fastgør skabet til en egnet vægkonstruktion, før donkraftene aflastes. Hold hænderne væk fra klempunkter, og tryk kun langsomt på udløseren, når belastningen er understøttet uafhængigt.
Fivalo™ 2-i-1 løfte- og støttebukkesæt til skabe (2-pak)
Lift, support, and align from a stable paired setup instead of rebuilding a stack of scraps every time the cabinet moves.
Two jacks. Three jobs. Both hands back on the install.
Stop balancing. Start aligning.
Scrap blocks can shift just when you need both hands. Place one jack near each end, raise in controlled steps, then level, shim, and fasten with the cabinet held at the working position.
One matched pair. Three ways to work.
Choose the configuration for the job, then stay inside the rating for that mode.
1. Support upper cabinets
Fit the wide support frames and use the pair beneath a cabinet after it has been safely placed at working height.
2. Lift and level
Use the broad contact plates for short-range positioning under base cabinets, furniture, and supported workpieces.
3. Clamp panel edges
Fit the clamp attachments for temporary workholding while you check flush alignment on compatible panel edges.
Control you can see before the first screw
The mechanism, scales, and contact surfaces are built around controlled positioning—not guesswork.
Scale-marked adjustment
Visible markings make paired height checks easier while you bring each side into position.
Broad contact surfaces
Wide ribbed support plates and rectangular slotted bases spread contact across the working surface.
Ratings matched to the mode
Up to 360 lb per pair for direct lifting; up to 180 lb per pair for extended cabinet support.
From first lift to final fastener
1. Place the pair
Work on flat, stable surfaces with one jack near each end and the load centered on the contact pads.
2. Raise in steps
Alternate between sides and watch the scale marks so the cabinet stays controlled as it reaches position.
3. Align and fasten
Check level and plumb, add required shims, then fasten to suitable wall structure using the cabinet maker’s instructions.
4. Unload, then release
Confirm the cabinet is independently secured, keep hands clear, and press each release gradually before removing the jacks.
Check alignment before the tools come out
The paired setup gives you time to verify level, reveal, and fastener placement while the cabinet stays supported. Once it is secured to the required wall structure, unload each jack and remove it from the work area.
Product details
Verified specifications
Set: 2 cabinet jack assemblies
Listed maximum extension: 23.4 in
Approximate base: 3.7 × 4.1 in
Approximate body height: 16 in
Scale-marked adjustment rails
Mode-specific ratings
Direct lift mode: up to 360 lb per pair.
Extended cabinet-support mode: up to 180 lb per pair.
Use the pair together, keep the load centered, and never exceed the rating for the selected configuration.
What’s included
2 × Cabinet jack assemblies
4 × Clip/support attachments in the two styles shown
6 × Protective covers
1 × Instruction manual
Safe use
Temporary positioning/support only; not structural shoring or overhead safety equipment. Inspect before use, work on flat stable surfaces, secure the cabinet independently before unloading, keep hands clear of pinch points, and press the release gradually.
Frequently asked questions
Can these jacks support an upper cabinet during installation?
Yes. The extended support frames are designed to hold a cabinet after it has been safely placed at working height. Use one jack near each end on a stable surface, then fasten the cabinet to suitable wall structure before unloading the jacks.
How high do they extend?
The manufacturer lists a maximum extension of 23.4 in. Measure from your stable working surface to the cabinet underside and allow for the contact pads before ordering.
What are the load ratings?
The pair is listed for up to 360 lb in direct lift mode and up to 180 lb in extended cabinet-support mode. Do not apply the higher lift rating to the extended support configuration.
Can one person install a cabinet with them?
The jacks can reduce the need to hold and balance the cabinet while aligning and fastening, but they do not replace safe lifting, suitable wall fasteners, or a second person when the cabinet or site conditions require one.
How do I lower the load?
First secure or independently support the load. Keep hands clear of pinch points and press the release gradually. No fine-descent claim is made, so maintain control and never release a loaded jack abruptly.
What comes in the set?
Two cabinet jack assemblies, four clip/support attachments in the two styles shown, six protective covers, and one instruction manual.
A matched two-jack system for installers who want fewer makeshift props and more control at the cabinet.