Build a simple under bed show storage with storage. It has a plexiglass cover so you can see inside and moveable dividers to keep the shows organized.

Difficulty : Moderate

Materials :

Wood Products

• Plywood (1) – 3/4" Thick, Half Sheet → 19 mm x Half Sheet Size (typically 1220 mm x 1220 mm)
• Board (2) – 1x6 x 96" → 19 mm x 152 mm x 2438 mm
• Board (4) – 1x4 x 96" → 19 mm x 102 mm x 2438 mm

Hardware & Supplies

• Plexiglass (1) – 3' x 3' → 914 mm x 914 mm
• Casters (4)
• Hinges (2)
• Cabinet Pull (1)
• 36 1/4" Pocket Hole Screws
• 20 3/4" Wood Screws

Cut List & Parts : 

• Base Plywood (1) – 3/4" x 29 3/4" x 33 3/4" → 19 mm x 756 mm x 857 mm
• Box Sides (Long) (2) – 1" x 6" x 33 3/4" → 25 mm x 152 mm x 857 mm
• Box Sides (Short) (2) – 1" x 6" x 31 3/4" → 25 mm x 152 mm x 806 mm
• Lid Side (Long) (2) – 1" x 4" x 31 1/4" → 25 mm x 102 mm x 794 mm
• Lid Side (Short) (2) – 1" x 4" x 30 1/4" → 25 mm x 102 mm x 768 mm
• Long Center Divider (1) – 1" x 4" x 33 3/4" → 25 mm x 102 mm x 857 mm
• Short Dividers (4) – 1" x 4" x 29 3/4" → 25 mm x 102 mm x 756 mm
• Plexiglass (1) – 29 1/4" x 33 1/4" → 743 mm x 844 mm

Directions : 

• Step 1 - Build the box

  Assemble the box for the shoe organizer using the 3/4" base plywood and the 1" x 6" sides. The pocket holes are all around the underside of the plywood as shown in the schematic.
  Join using 1 1/4" pocket hole screws and wood glue. Ensure everything is square.

  
  
  

  2 - Build the box- 2

  Also add pocket hole screws to the insides of the opposite sides as show in the schematic.

  
  
  

  3 - Build frame for Lid

  Build a frame for the lid using the 1x4 boards using 1 1/4" pocket hole screws and wood glue. Ensure everything is square.

  
  
  

  4 - Attach plexiglass

  Attach plexiglass to the inside of the lid using 3/4" wood screws.
  To do this - pre-drill holes slowly in the plexiglass and then add screws. Be careful not to over tighten.

  Note - you can also route out the insides of the lid before building the frame to inset the Plexiglas.. I wanted to keep this a simple build that didn't involve a lot of tools.

  
  
  

  5 - Cut dividers

  Cut up the 1" x 4" dividers for the organizer as shown in the picture. This gives a 10 shoe organizer. You can add extra slits in the long divider to add more options for the arrangement.
  The dividers fit snug and hence are not attached to the box.

  
  
  

  6 - Finishing touches

  Sand and stain or paint per your choice.

  Attach the lid to the box using hinges.
  Add casters on the bottom and a pull to the front of the box.

  
  
  

  7 - See more information

  For more details on this project, please see - https://www.anikasdiylife.com/diy-under-bed-shoe-organizer/

  Video tutorial at - https://youtu.be/0IGCQN-VmmE